Fuel placement and air-fuel mixing in a generic aeroengine premix module employing plain jet liquid fuel injection into a counter-swirling double-annular crossflow were investigated at different values of air inlet pressure (6 bar, 700 K and 12 bar, 700 K) and liquid-to-air momentum flux ratio, both parameters being a function of engine power. Kerosene Jet A-1 was used as liquid fuel. Measurement techniques included LDA for investigation of the airflow and Mie-scattering laser light sheets and PDA for investigation of the two-phase flow. Measurements were taken at various axial distances from the fuel nozzle equivalent to mean residence times of up to 0.47 ms. It was found that the initial fuel placement reacts very sensitively to a variation of liquid-to-air momentum flux ratio. Susceptibility of the spray to dispersion due to centrifugal forces and to turbulent mixing is primarily a function of the fuel droplet diameters, which in turn depend on operating pressure. The data are interpreted by evaluation of the corresponding Stokes numbers.
Skip Nav Destination
Article navigation
October 2003
Technical Papers
Liquid Fuel Placement and Mixing of Generic Aeroengine Premix Module at Different Operating Conditions
J. Becker
DLR–German Aerospace Center, Institute of Propulsion Technology, 51170 Cologne, Germany
C. Hassa
DLR–German Aerospace Center, Institute of Propulsion Technology, 51170 Cologne, Germany
Contributed by the International Gas Turbine Institute (IGTI) of THE AMERICAN SOCIETY OF MECHANICAL ENGINEERS for publication in the ASME JOURNAL OF ENGINEERING FOR GAS TURBINES AND POWER. Paper presented at the International Gas Turbine and Aeroengine Congress and Exhibition, Amsterdam, The Netherlands, June 3–6, 2002; Paper No. 2002-GT-30102. Manuscript received by IGTI, Dec. 2001, final revision, Mar. 2002. Associate Editor: E. Benvenuti.
J. Eng. Gas Turbines Power. Oct 2003, 125(4): 901-908 (8 pages)
Published Online: November 18, 2003
Article history
Received:
December 1, 2001
Revised:
March 1, 2002
Online:
November 18, 2003
Citation
Becker , J., and Hassa, C. (November 18, 2003). "Liquid Fuel Placement and Mixing of Generic Aeroengine Premix Module at Different Operating Conditions ." ASME. J. Eng. Gas Turbines Power. October 2003; 125(4): 901–908. https://doi.org/10.1115/1.1587741
Download citation file:
Get Email Alerts
Shape Optimization of an Industrial Aeroengine Combustor to reduce Thermoacoustic Instability
J. Eng. Gas Turbines Power
Dynamic Response of A Pivot-Mounted Squeeze Film Damper: Measurements and Predictions
J. Eng. Gas Turbines Power
Review of The Impact Of Hydrogen-Containing Fuels On Gas Turbine Hot-Section Materials
J. Eng. Gas Turbines Power
Effects of Lattice Orientation Angle On Tpms-Based Transpiration Cooling
J. Eng. Gas Turbines Power
Related Articles
Effects of Fuel Nozzle Displacement on Pre-Filming Airblast Atomization
J. Eng. Gas Turbines Power (January,2001)
Modeling Mixture Formation in a Gasoline Direct Injection Engine
J. Appl. Mech (November,2006)
A Comparison of Single and Multiphase Jets in a Crossflow Using Large Eddy Simulations
J. Eng. Gas Turbines Power (January,2007)
Low Swirl Effect on Compact Spray and Combustion Systems Using Additive Manufactured Dual Airblast Injectors
J. Eng. Gas Turbines Power (December,2024)
Related Proceedings Papers
Related Chapters
Fuel Nozzle Geometry Effects on Cavitation and Spray Behavior at Diesel Engine Conditions
Proceedings of the 10th International Symposium on Cavitation (CAV2018)
Antilock-Braking System Using Fuzzy Logic
International Conference on Mechanical and Electrical Technology, 3rd, (ICMET-China 2011), Volumes 1–3
A Simple Carburetor
Case Studies in Fluid Mechanics with Sensitivities to Governing Variables