Atomic force microscopy (AFM) is one of the most effective tools in nanotechnology researches. Using the raster scanning method with a soft cantilever, three dimensional sample surface topography can be obtained with a sub-nanometer resolution. In this study, AFM is employed to characterize the nanostructures of polymer film under two temperature treatments. 3-aminopropyltriethoxysilane (APTES) is selected as a model polymer molecule due to its wide applications for amino-functionalization of Si/SiOx based surfaces, such as silicon and mica. The APTES molecule has three ethoxy groups that can react with surface hydroxyl groups or with another APTES molecule through a siloxane bond. The self-assembled APTES self-assembly film has typically three configurations, namely uncrosslinked monolayer, crosslinked monolayer, and multilayer. Ten percent aqueous solution is used to cover the entire mica surfaces. Then the surfaces are rinsed with DI water and dried with N2 to remove left over solution. Two hours incubation was followed in 80°C or 140°C, respectively. At 80 °C (below the boiling point), the uniform APTES film is obtained. On the other hand, at 140 °C (above the boiling point), the film exhibits multilayer structure, as confirmed by AFM images. Contact angle measurement shows that the multilayer film is less wettable than the monolayer film by 20°. It seems that the evaporation rate of the water layer on the substrate is the key to various film configurations.
Skip Nav Destination
Article navigation
Photo Gallery
Atomic Force Microscopy (AFM) as a Powerful Tool to Study Temperature-Dependent Polymer Film Formation
Fei Long,
Fei Long
Michigan Technological University, Houghton, MI 49931
flong@mtu.edu
flong@mtu.edu
Search for other works by this author on:
Chang Kyoung Choi
Chang Kyoung Choi
Michigan Technological University, Houghton, MI 49931
cchoi@mtu.edu
cchoi@mtu.edu
Search for other works by this author on:
Fei Long
Michigan Technological University, Houghton, MI 49931
flong@mtu.edu
flong@mtu.edu
Chang Kyoung Choi
Michigan Technological University, Houghton, MI 49931
cchoi@mtu.edu
cchoi@mtu.edu
1Corresponding author.
J. Heat Transfer. Feb 2017, 139(2): 020904
Published Online: January 6, 2017
Article history
Received:
November 4, 2016
Revised:
November 17, 2016
Citation
Long, F., and Choi, C. K. (January 6, 2017). "Atomic Force Microscopy (AFM) as a Powerful Tool to Study Temperature-Dependent Polymer Film Formation." ASME. J. Heat Transfer. February 2017; 139(2): 020904. https://doi.org/10.1115/1.4035574
Download citation file:
62
Views
Get Email Alerts
Cited By
Related Articles
Thermomechanical Formation of Nanoscale Polymer Indents With a Heated Silicon Tip
J. Heat Transfer (November,2007)
Nanoscale Temperature Distributions Measured by Scanning Joule Expansion Microscopy
J. Heat Transfer (May,1998)
Electric-Field-Assisted Contact Mode Atomic Force Microscope-Based Nanolithography With Low Stiffness Conductive Probes
J. Micro Nano-Manuf (March,2022)
Development of Nanoporous Ultrathin Membranes For Implantable Drug Delivery
J. Med. Devices (June,2008)
Related Proceedings Papers
Related Chapters
Chitosan-Based Drug Delivery Systems
Chitosan and Its Derivatives as Promising Drug Delivery Carriers
Introduction
Bacteriophage T4 Tail Fibers as a Basis for Structured Assemblies
Neural Network Modeling in Nanotechnology: The Development of Nanostructures Produced by Molecular Beam Epitaxy for Infrared Applications
Intelligent Engineering Systems through Artificial Neural Networks, Volume 16