Abstract

The test results from a composite material round robin manufacturing study are presented. The objective of the study was to investigate material property variability when different manufacturers were used to fabricate identical composite parts. The study was part of an ongoing Office of Naval Research project to determine the causes of material property variability of E-glass/vinyl-ester structural composites fabricated with a vacuum-assisted resin transfer molding process. The manufacturers that participated in the study consisted of five industrial composite fabricators that either had experience with U.S. naval fabrication projects or possessed commercial marine fabrication experience. The materials specified for the study were a 24 oz woven roving E-glass fabric and a rubber-toughened vinyl-ester resin system. The tests performed included constituent volume, tension, compression, in-plane shear, and flexure. The material coupon tests were performed on 5.1 mm (0.20 in.) thick cross-ply laminates in a warps parallel lay-up. A three-dimensional digital image correlation system was used to measure strain during testing to reduce the variability often experienced when using conventional foil strain gauges on heavy woven fabrics. The results of the testing indicated that compression had the most variability in both strength and modulus, which was attributed to the waviness of the fabric, while the flexural strength and tensile modulus had the least amount of variability.

References

1.
El-Chiti
,
F.
,
2005
, “
Experimental Variability of E-Glass Reinforced Vinyl Ester Composites Fabricated by VARTM/SCRIMP
,” M.S. thesis in Mechanical Engineering,
University of Maine
, Orono, Maine.
2.
Cain
,
J.
,
Post
,
N. L.
,
Lesko
,
J. J.
,
Case
,
S. W.
,
Lin
,
Y.
,
Riffle
,
J. S.
, and
Hess
,
P. E.
, “
Post-Curing Effects on Marine VARTM FRP Composite Material Properties for Test and Implementation
,”
J. Eng. Mater. Technol.
 0094-4289, Vol.
128
(
1
),
2006
, pp.
34
40
. https://doi.org/10.1115/1.2128425
3.
ASTM D2584,
2002
, “
Standard Test Method for Ignition Loss of Cured Reinforced Resins
,” Annual Book of ASTM Standards, Vol.
08.01
, ASTM International, West Conshohocken, PA.
4.
ASTM D3039,
2007
, “
Standard Test Method for Tensile Properties of Polymer Matrix Composite Materials
,” Annual Book of ASTM Standards, Vol.
15.03
, ASTM International, West Conshohocken, PA.
5.
ASTM D6641,
2001
, “
Standard Test Method for Determining the Compressive Properties of Polymer Matrix Composite Laminates Using a Combined Loading Compression (CLC) Test Fixture
,” Annual Book of ASTM Standards, Vol.
15.03
, ASTM International, West Conshohocken, PA.
6.
ASTM D4255-01,
2001
, “
Standard Test Method for In Plane Shear Properties of Polymer Matrix Composite Materials by the Rail Shear Method
,” Annual Book of ASTM Standards, Vol.
15.03
, ASTM International, West Conshohocken, PA.
7.
ASTM D7264-07,
2007
, “
Standard Test Method for Flexural Properties of Polymer Matrix Composite Materials
,” Annual Book of ASTM Standards, Vol.
15.03
, ASTM International, West Conshohocken, PA.
8.
Masters
,
J.
, “
Strain Gage Selection Criteria for Textile Composite Materials
,” NASA Contractor Report 198286, National Aeronautics and Space Administration, Langley Research Center, Hampton, Virginia,
1996
.
9.
Lopez-Anido
,
R.
,
El-Chiti
,
F. W.
,
Muszynski
,
L.
,
Dagher
,
H. J.
,
Thompson
,
L.
, and
Hess
,
P. E.
, “
Composite Material Testing Using a 3-D Digital Image Correlation System
,”
Proceedings of the ACMA Composites 2004 Convention and Trade Show
, Tampa, FL, October 6–8,
2004
,
American Composites Manufacturers Association
,
Arlington, VA
.
10.
El-Chiti
,
F.
,
Lopez-Anido
,
R. A.
,
Dagher
,
H. J.
,
Thompson
,
L.
,
Muszynski
,
L.
, and
Hess
,
P. E.
, “
Experimental Approach for Characterizing VARTM Composites Using a 3-D Digital Image Correlation System
,”
Proceedings of the SEM XII Int. Congress and Exposition on Experimental and Applied Mechanics
, Portland, OR, June 7–9,
2005
,
Society for Experimental Mechanics
,
Bethel, CT
, 8 pp.
11.
Hammami
A.
and
Al-Ghuilani
N.
, “
Durability and Environmental Degradation of Glass-Vinylester Composites
,”
Polym. Compos.
 0272-8397, Vol.
25
(
6
),
2004
, pp.
609
-
616
. https://doi.org/10.1002/pc.20055
12.
Karbhari
,
V. M.
and
Zhang
,
S.
, “
E-Glass/Vinyl Ester Composites in Aqueous Environments—I: Experimental Results
,”
Appl. Compos. Mater.
 0929-189X, Vol.
10
,
2003
, pp.
19
48
. https://doi.org/10.1023/A:1021153315780
13.
Puccini
,
G.
, “
Environmental Aspects
,”
Composite Materials in Maritime Structures
,
R. A.
Shenoi
, Ed.,
Cambridge University Press
,
Cambridge, UK
,
1993
, Vol.
1
.
14.
Tarnopol’skii
Y. M.
and
Kulakov
Y. L.
, “
Tests Methods for Composites
,”
Mech. Compos. Mater.
 0191-5665, Vol.
37
(
5/6
),
2001
, pp.
431
-
448
.
15.
Lee
,
J.
and
Soutis
,
C.
, “
A Study on the Compressive Strength of Thick Carbon Fibre/Epoxy Laminates
,”
Compos. Sci. Technol.
 0266-3538, Vol.
67
(
10
),
2007
, pp.
2015
2026
. https://doi.org/10.1016/j.compscitech.2006.12.001
16.
Lavoie
,
J. A.
,
Soutis
,
C.
, and
Morton
,
J.
, “
Apparent Strength Scaling in Continuous Fiber Composite Laminates
,”
Compos. Sci. Technol.
 0266-3538, Vol.
60
(
2
),
2000
, pp.
283
299
. https://doi.org/10.1016/S0266-3538(99)00124-4
17.
Walls
J.
and
Thompson
L.
, “
Parametric Shape Optimization of Tensile Coupons for Marine Grade Glass Fiber Reinforced Plastics
,” Report No. ATS-RELY/2-2005-02, Applied Thermal Sciences, Orono, Maine,
2005
.
18.
Berube
,
K. A.
and
Lopez-Anido
,
R.
, “
Full-field Strain Measurements for Determining Mechanical Properties of Marine Composite Laminates
,”
Experimental Mechanics Applied to Damage: Detection, Analysis and Mitigation, SEM XI International Congress Exposition on Experimental and Applied Mechanics
, Orlando, FL, June 2–5,
2008
,
Society for Experimental Mechanics
,
Bethel, CT
, 8 pp.
19.
MIL 17–The Composite Materials Handbook, Vol. 1: Polymer Matrix Composites: Guidelines for Characterization of Structural Materials
, Vol.
1
,
ASTM International
,
West Conshohocken, PA
,
2002
, 585 pp.
20.
Yang
,
B.
,
Kozeya
,
V.
,
Adanurb
,
S.
, and
Kumara
,
S.
, “
Bending, Compression, and Shear Behavior of Woven Glass Fiber-Epoxy Composites
,”
Composites, Part B
 1359-8368, Vol.
31
,
2000
, pp.
715
721
. https://doi.org/10.1016/S1359-8368(99)00052-9
21.
Kim
,
J.
,
Shioya
,
M.
,
Kobayashi
,
H.
,
Junichi Kaneko
,
J.
, and
Kido
,
M.
, “
Mechanical Properties of Woven Laminates and Felt Composites Using Carbon Fibers. Part 1: In-Plane Properties
,”
Compos. Sci. Technol.
 0266-3538, Vol.
64
,
2004
, pp.
2221
2229
. https://doi.org/10.1016/j.compscitech.2004.03.012
This content is only available via PDF.
You do not currently have access to this content.