Skip Nav Destination
Issues
Research Papers
Modeling of Three-Dimensional Effects on Fatigue Crack Closure Processes in Small-Scale Yielding
J. ASTM Int.. May 2005, 2(5): 1–19.
doi: https://doi.org/10.1520/JAI11986
Crack Initiation, Propagation, and Arrest in 316L Model Pipe Components under Thermal Fatigue
J. ASTM Int.. May 2005, 2(5): 1–18.
doi: https://doi.org/10.1520/JAI12035
The Effect of Negative Stress Ratio Load History on High Cycle Fatigue Threshold
J. ASTM Int.. May 2005, 2(5): 1–17.
doi: https://doi.org/10.1520/JAI12042
Progress in the Characterization of the Cutting Resistance of Protective Materials
J. ASTM Int.. May 2005, 2(5): 1–15.
doi: https://doi.org/10.1520/JAI12148
On Secondary β-Nb Phase Precipitation within Primary α-Zr Phase in Zr-Nb Alloys During Tensile Deformation
J. ASTM Int.. May 2005, 2(5): 1–27.
doi: https://doi.org/10.1520/JAI12198
Development of SRMs 295x and 296x, Respirable Crystalline Silica on Filter
J. ASTM Int.. May 2005, 2(5): 1–8.
doi: https://doi.org/10.1520/JAI12239
An Overview of Fundamental and Simulative Performance Tests for Hot Mix Asphalt
J. ASTM Int.. May 2005, 2(5): 1–15.
doi: https://doi.org/10.1520/JAI12254
Study of Nb and Fe Precipitation in α-Phase Temperature Range (400 to 550°C) in Zr-Nb-(Fe-Sn) Alloys
J. ASTM Int.. May 2005, 2(5): 1–18.
doi: https://doi.org/10.1520/JAI12321
Predicting Oxidation and Deuterium Ingress for Zr-2.5Nb CANDU Pressure Tubes
J. ASTM Int.. May 2005, 2(5): 1–14.
doi: https://doi.org/10.1520/JAI12342
In-Core Tests of Effects of BWR Water Chemistry Impurities on Zircaloy Corrosion
J. ASTM Int.. May 2005, 2(5): 1–26.
doi: https://doi.org/10.1520/JAI12373
Microstructure and Growth Mechanism of Oxide Layers Formed on Zr Alloys Studied with Micro-Beam Synchrotron Radiation
J. ASTM Int.. May 2005, 2(5): 1–26.
doi: https://doi.org/10.1520/JAI12375
Ductility of Zircaloy-4 Fuel Cladding and Guide Tubes at High Fluences
J. ASTM Int.. May 2005, 2(5): 1–26.
doi: https://doi.org/10.1520/JAI12423
Injury Rates and Injury Types in Alpine Skiing, Telemarking, and Snowboarding
J. ASTM Int.. May 2005, 2(5): 1–9.
doi: https://doi.org/10.1520/JAI12526
Predicting Fatigue Crack Growth in the Residual Stress Field of a Cold Worked Hole
J. ASTM Int.. May 2005, 2(5): 1–13.
doi: https://doi.org/10.1520/JAI12556
Stress Intensity Factor Analysis and Fatigue Behavior of a Crack in the Residual Stress Field of Welding
J. ASTM Int.. May 2005, 2(5): 1–11.
doi: https://doi.org/10.1520/JAI12558
Microstructure and Phase Control in Zr-Fe-Cr-Ni Alloys: Thermodynamic and Kinetic Aspects
J. ASTM Int.. May 2005, 2(5): 1–28.
doi: https://doi.org/10.1520/JAI12771
Estimation of Compressive Strength of Recycled Concretes with the Ultrasonic Method
J. ASTM Int.. May 2005, 2(5): 1–8.
doi: https://doi.org/10.1520/JAI12849
Corrosion Behavior of Heat-Treated Duplex Stainless Steels in Saturated Carbon Dioxide-Chloride Solutions
J. ASTM Int.. May 2005, 2(5): 1–11.
doi: https://doi.org/10.1520/JAI12866
Understanding Polymeric Pads in Pre-CMP Conditioning
J. ASTM Int.. May 2005, 2(5): 1–11.
doi: https://doi.org/10.1520/JAI12894
Effects of Proposed Well-Graded Aggregate Gradations on Frost Durability of Concrete
J. ASTM Int.. May 2005, 2(5): 1–14.
doi: https://doi.org/10.1520/JAI12940
Evaluation of Different Techniques for Adhesive Properties of Asphalt-Filler Systems at Interfacial Region
J. ASTM Int.. May 2005, 2(5): 1–15.
doi: https://doi.org/10.1520/JAI12961
Investigation into Flow Property Measurements of Low-Slump Concrete Using Vibrating Slope Apparatus (VSA)
J. ASTM Int.. May 2005, 2(5): 1–18.
doi: https://doi.org/10.1520/JAI13054
Photo Thermal Micro-Spectroscopy — A New Method for Infared Analysis of Materials
J. ASTM Int. (November 2005)
Correlation between Thermal and Mechanical Properties of the 10NiCr11
J. ASTM Int. (June 2009)
Correlation Between Charpy Absorbed Energy Using 2 mm and 8 mm Strikers
J. ASTM Int. (October 2011)
Low-Level Sulfur in Fuel Determination Using Monochromatic WD XRF—ASTM D 7039-04
J. ASTM Int. (September 2005)
Electrochemical Techniques in Corrosion: Status, Limitations, and Needs
J. ASTM Int. (February 2008)
