Skip Nav Destination
Issues
Research Papers
Further Results on Attenuation of Neutron Embrittlement Effects in a Simulated RPV Wall
J. ASTM Int.. May 2010, 7(5): 1–11.
doi: https://doi.org/10.1520/JAI102070
Development of a Standard Flammability Test for Water-Based Hydraulic Fluids
J. ASTM Int.. May 2010, 7(5): 1–10.
doi: https://doi.org/10.1520/JAI102325
The Analysis of Fracture Mechanisms of Ferritic Steel 13HMF at Low Temperatures
J. ASTM Int.. May 2010, 7(5): 1–14.
doi: https://doi.org/10.1520/JAI102470
Mesh-Free Solution of Two-Dimensional Edge Crack Problems under Thermo-Mechanical Load
J. ASTM Int.. May 2010, 7(5): 1–12.
doi: https://doi.org/10.1520/JAI102517
Phase Change and Mechanical Behaviors of TixCoCrFeNiCu1−yAly High Entropy Alloys
J. ASTM Int.. May 2010, 7(5): 1–8.
doi: https://doi.org/10.1520/JAI102527
Modeling of Crack Propagation in Weld Beam-to-Column Connections Submitted to Cyclic Loading with a Cohesive Zone Model
J. ASTM Int.. May 2010, 7(5): 1–15.
doi: https://doi.org/10.1520/JAI102531
Mechanical Conditioning of Superelastic Nitinol Wire for Improved Fatigue Resistance
J. ASTM Int.. May 2010, 7(5): 1–7.
doi: https://doi.org/10.1520/JAI102547
Sub-Surface Initiated Rolling Contact Fatigue—Influence of Non-Metallic Inclusions, Processing History, and Operating Conditions
J. ASTM Int.. May 2010, 7(5): 1–12.
doi: https://doi.org/10.1520/JAI102559
Measurement of Mechanical Properties of Hydrated Cement Paste Using Resonant Ultrasound Spectroscopy
J. ASTM Int.. May 2010, 7(5): 1–8.
doi: https://doi.org/10.1520/JAI102657
Test Method for Determining the Efflorescence Potential of Masonry Materials Based on Soluble Salt Content
J. ASTM Int.. May 2010, 7(5): 1–11.
doi: https://doi.org/10.1520/JAI102725
Efflorescence: Evaluation of Published Test Methods for Brick and Efforts to Develop a Masonry Assembly Test Method
J. ASTM Int.. May 2010, 7(5): 1–7.
doi: https://doi.org/10.1520/JAI102744
Finite Element Modeling of a Rockman Portable Dynamic Hardness Tester
J. ASTM Int.. May 2010, 7(5): 1–11.
doi: https://doi.org/10.1520/JAI102757
Performance of Olive Waste Ash Concrete Exposed to Thermal Cycling
J. ASTM Int.. May 2010, 7(5): 1–11.
doi: https://doi.org/10.1520/JAI102777
Design and Use of Expansion Joints in New and Existing Clay Masonry Wall Systems
J. ASTM Int.. May 2010, 7(5): 1–18.
doi: https://doi.org/10.1520/JAI102864
Comparative Study of Freeze and Thaw Test Procedures on Molded Brick
J. ASTM Int.. May 2010, 7(5): 1–8.
doi: https://doi.org/10.1520/JAI102882
Resistance of protective gloves materials to puncture by medical needles
J. ASTM Int.. May 2010, 7(5): 1–16.
doi: https://doi.org/10.1520/JAI102923
The Effect of Microstructure on Delayed Hydride Cracking Behavior of Zircaloy-4 Fuel Cladding—An International Atomic Energy Agency Coordinated Research Program
C. Coleman, V. Grigoriev, V. Inozemtsev, V. Markelov, M. Roth, V. Makarevicius, Y. S. Kim, Kanwar Liaqat Ali, J. K. Chakravarrty, R. Mizrahi, R. Lalgudi
J. ASTM Int.. May 2010, 7(5): 1–20.
doi: https://doi.org/10.1520/JAI103008
Loading Mixity on the Interfacial Failure Mode in Lead-Free Solder Joint
J. ASTM Int.. May 2010, 7(5): 1–15.
doi: https://doi.org/10.1520/JAI103021
Tensile Properties of Sn-10Sb-5Cu High Temperature Lead Free Solder
J. ASTM Int.. May 2010, 7(5): 1–7.
doi: https://doi.org/10.1520/JAI103041
Wetting Behavior of Solders
J. ASTM Int.. May 2010, 7(5): 1–18.
doi: https://doi.org/10.1520/JAI103055
A Prospective Study of Injuries in NCAA Intercollegiate Ice-Hockey Goaltenders
J. ASTM Int. (March 2009)
Stabilization of Suspension Concentrate Formulations via Specialized Double-comb Polymers
J. ASTM Int. (June 2009)
Study on Flaking Process in Bearings by White Etching Area Generation
J. ASTM Int. (May 2006)
More Accurate Approximation of J-Integral Equation for Evaluating Fracture Resistance Curves
J. ASTM Int. (January 2010)
