Skip Nav Destination
Issues
Research Papers
Rolling Contact Fatigue Life Test Design and Result Interpretation Methods Maintaining Compatibility of Efficiency and Reliability
J. ASTM Int.. June 2010, 7(6): 1–14.
doi: https://doi.org/10.1520/JAI102492
Immobilization of Cellulase and Hemicellulases on Porous Glass Beads
J. ASTM Int.. June 2010, 7(6): 1–10.
doi: https://doi.org/10.1520/JAI102580
Effects of Analytical Precision on Bogue Calculations of Potential Portland Cement Composition
J. ASTM Int.. June 2010, 7(6): 1–18.
doi: https://doi.org/10.1520/JAI102697
Residual Strain Effects on Bridging Stress of Cracked and Delaminated Fiber Metal Laminates
J. ASTM Int.. June 2010, 7(6): 1–24.
doi: https://doi.org/10.1520/JAI102698
Fatigue Crack Propagation Behavior of an Inertia Friction Welded α/β Titanium Alloy
J. ASTM Int.. June 2010, 7(6): 1–14.
doi: https://doi.org/10.1520/JAI102710
Common Sense and Masonry Repair
J. ASTM Int.. June 2010, 7(6): 1–15.
doi: https://doi.org/10.1520/JAI102727
Analysis of Impact of Various Factors on Downwind Deposition Using a Simulation Method
J. ASTM Int.. June 2010, 7(6): 1–11.
doi: https://doi.org/10.1520/JAI102771
Evaluation of Spray Drift Using Low-Speed Wind Tunnel Measurements and Dispersion Modeling
Bradley K. Fritz, W. Clint Hoffmann, Norman B. Birchfield, Jay Ellenberger, Faruque Khan, W. E. Bagley, Jonathan W. Thornburg, Andrew Hewitt
J. ASTM Int.. June 2010, 7(6): 1–14.
doi: https://doi.org/10.1520/JAI102775
Analyzing the Riding Behavior of Recreational Skiers and Snowboarders
J. ASTM Int.. June 2010, 7(6): 1–8.
doi: https://doi.org/10.1520/JAI102814
Design Development of Large Thermoplastic Chambers for Stormwater Retention
J. ASTM Int.. June 2010, 7(6): 1–12.
doi: https://doi.org/10.1520/JAI102861
Effect of Hard Water and Ammonium Sulfate on Weak Acid Herbicide Activity
J. ASTM Int.. June 2010, 7(6): 1–10.
doi: https://doi.org/10.1520/JAI102869
Simulation of Outside-in Cracking in Boiling Water Reactor Fuel Cladding Tubes under Power Ramp
J. ASTM Int.. June 2010, 7(6): 1–12.
doi: https://doi.org/10.1520/JAI102938
Retention Requirements for Alpine Ski Bindings
J. ASTM Int.. June 2010, 7(6): 1–22.
doi: https://doi.org/10.1520/JAI102978
Performance of Zirconium Alloys in Light Water Reactors with a Review of Nodular Corrosion
J. ASTM Int.. June 2010, 7(6): 1–15.
doi: https://doi.org/10.1520/JAI103032
Ball Grid Array Lead-Free Solder Joint Strength under Monotonic Flexural Load
J. ASTM Int.. June 2010, 7(6): 1–14.
doi: https://doi.org/10.1520/JAI103044
Photo Thermal Micro-Spectroscopy — A New Method for Infared Analysis of Materials
J. ASTM Int. (November 2005)
Correlation between Thermal and Mechanical Properties of the 10NiCr11
J. ASTM Int. (June 2009)
Correlation Between Charpy Absorbed Energy Using 2 mm and 8 mm Strikers
J. ASTM Int. (October 2011)
Low-Level Sulfur in Fuel Determination Using Monochromatic WD XRF—ASTM D 7039-04
J. ASTM Int. (September 2005)
Electrochemical Techniques in Corrosion: Status, Limitations, and Needs
J. ASTM Int. (February 2008)
