The recent application of inkjet printing to fabrication of three-dimensional, multilayer and multimaterial parts has tested the limits of conventional printing-based additive manufacturing techniques. The novel method presented here, termed as additive manufacturing via microarray deposition (AMMD), expands the allowable range of physical properties of printed fluids to include important, high-viscosity production materials (e.g., polyurethane resins). AMMD relies on a piezoelectrically driven ultrasonic print-head that generates continuous streams of droplets from orifices while operating in the 0.5–3.0 MHz frequency range. The device is composed of a bulk ceramic piezoelectric transducer for ultrasound generation, a reservoir for the material to be printed, and a silicon micromachined array of liquid horn structures, which make up the ejection nozzles. Unique to this new printing technique are the high frequency of operation, use of fluid cavity resonances to assist ejection, and acoustic wave focusing to generate the pressure gradient required to form and eject droplets. We present the initial characterization of a micromachined print-head for deposition of fluids that cannot be used with conventional printing-based rapid prototyping techniques. Glycerol-water mixtures with a range of properties (surface tensions of and viscosities of ) were used as representative printing fluids for most investigations. Sustained ejection was observed in all cases. In addition, successful ejection of a urethane-based photopolymer resin (surface tension of and viscosity of ) was achieved in short duration bursts. Peaks in the ejection quality were found to correspond to predicted device resonances. Based on these results, we have demonstrated the printing of fluids that fall well outside of the accepted range for the previously introduced printing indicator. The micromachined ultrasonic print-head achieves sustained printing of fluids up to , far above the typical printable range.
Skip Nav Destination
e-mail: j.mark.meacham@opencelltech.com
Article navigation
June 2010
Special Issue On Nanomanufacturing
Micromachined Ultrasonic Print-Head for Deposition of High-Viscosity Materials
J. Mark Meacham,
e-mail: j.mark.meacham@opencelltech.com
J. Mark Meacham
OpenCell Technologies
, 500 Bishop Street Northwest, Suite E3, Atlanta, GA 30318
Search for other works by this author on:
Amanda O’Rourke,
Amanda O’Rourke
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
Search for other works by this author on:
Yong Yang,
Yong Yang
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
Search for other works by this author on:
Andrei G. Fedorov,
Andrei G. Fedorov
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
Search for other works by this author on:
F. Levent Degertekin,
F. Levent Degertekin
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
Search for other works by this author on:
David W. Rosen
David W. Rosen
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
Search for other works by this author on:
J. Mark Meacham
OpenCell Technologies
, 500 Bishop Street Northwest, Suite E3, Atlanta, GA 30318e-mail: j.mark.meacham@opencelltech.com
Amanda O’Rourke
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
Yong Yang
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
Andrei G. Fedorov
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
F. Levent Degertekin
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332
David W. Rosen
George W. Woodruff School of Mechanical Engineering,
Georgia Institute of Technology
, 813 Ferst Drive Northwest, Atlanta, GA 30332J. Manuf. Sci. Eng. Jun 2010, 132(3): 030905 (11 pages)
Published Online: May 19, 2010
Article history
Received:
April 20, 2009
Revised:
April 6, 2010
Online:
May 19, 2010
Published:
May 19, 2010
Citation
Meacham, J. M., O’Rourke, A., Yang, Y., Fedorov, A. G., Degertekin, F. L., and Rosen, D. W. (May 19, 2010). "Micromachined Ultrasonic Print-Head for Deposition of High-Viscosity Materials." ASME. J. Manuf. Sci. Eng. June 2010; 132(3): 030905. https://doi.org/10.1115/1.4001551
Download citation file:
Get Email Alerts
Cited By
Special Issue on the State-of-the-Art in Japanese Manufacturing Research
J. Manuf. Sci. Eng
A Review of Advanced Roll-to-Roll Manufacturing: System Modeling and Control
J. Manuf. Sci. Eng (April 2025)
Related Articles
Ejection Process Simulation for a Piezoelectric Microdroplet Generator
J. Fluids Eng (November,2006)
Deformation of a Droplet in a Channel Flow
J. Fuel Cell Sci. Technol (November,2008)
Marangoni and Variable Viscosity Phenomena in Picoliter Size Solder Droplet Deposition
J. Heat Transfer (April,2003)
Computational Fluid Dynamic Analysis of Eccentric Atomization Spray Cooling Nozzle Designs for Micromachining
J. Micro Nano-Manuf (June,2014)
Related Proceedings Papers
Related Chapters
Droplet and Deposit Patterns of One Pseudoplastic and Three Newtonian Spray Mixtures Following Spray Application Under Laboratory Conditions
Pesticide Formulations and Application Systems: Eighth Volume
Scale-Effect Investigation of Cavitation Erosion Using the Energy Parameter
Erosion by Cavitation or Impingement
Effect of Adjuvants on Physical Properties of Glyphosate and PPO-Inhibiting Herbicide Spray Mixtures
Pesticide Formulation and Delivery Systems: 39th Volume, Innovative Formulation, Application and Adjuvant Technologies for Agriculture