Abstract

The isothermal transformation of bainite in an advanced high-strength steel (AHSS) in the temperature range of 422°C to 482°C for transformation times of 10–6000 s has been examined using light optical microscopy (LOM), and orientation imaging microscopy (OIM). Thermodynamic calculations were done using equilibrium thermodynamic simulation software to produce a theoretical time-temperature-transformation (TTT) diagram, to which the experimental results of this study were compared. Advanced microstructural techniques, such as orientation-imaging-microscopy–electron-backscatter-diffraction (OIM-EBSD), image quality (IQ) phase identification, and polarized light microscopy, were used to observe and quantify the progress of the bainitic transformation during isothermal transformation. Orientation imaging microscopy using electron backscatter diffraction image quality (EBSD-IQ) was used with each sample to quantify the amount of bainite transformed. Results showed that the isothermal transformation at 422°C had 80.1 % bainite, whereas the isothermal transformation at 482°C had 85.5 % bainite transformed after 1200 s; while, after 6000 s, the amount of bainite increased to 90.1 % and 93.4 % respectively. As a result the chemical composition of the steel investigated and the microstructural characteristics of the bainite observed, it was not possible to discern the type of bainite formed at higher and lower temperatures because of the absence of carbides. The kinetics of transformation from the experimental results clearly indicated that the isothermal transformation is slower than that predicted by the theoretical thermodynamic program. The results of this study are presented and discussed.

References

1.
Demeri
,
M. Y.
,
Advanced High-Strength Steels: Science, Technology, and Applications
,
ASM International
,
Materials Park, OH
,
2013
, p. 59.
2.
Bhattacharya
,
D.
, “
Microalloyed Steels for the Automotive Industry
,”
Technol. Metal. Mater. Miner.
, Vol.
11
, No.
4
,
2014
pp.
371
383
.
3.
ASTM E3-11,
Standard Guide for Preparation of Metallographic Specimens
,
ASTM International
,
West Conshohocken, PA
,
2010
, www.astm.org
4.
Bechet
,
S.
and
Beaujard
,
L.
, “
New Reagent for the Micrographical Demonstration of the Austenite Grain of Hardened or Hardened-Tempered Steels
,”
Rev. Met.
, Vol.
52
, No.
10
,
1955
, pp.
830
836
.
5.
Zakerinia
,
H.
,
Kermanpur
,
A.
, and
Najafizadeh
,
A.
, “
The Effect of Bainite in Producing Nano/Ultrafine Grained Steel by the Martensite Treatment
,”
Mater. Sci. Eng.
, Vol.
528
, Nos.
10–11
,
2011
, pp.
3562
3567
. https://doi.org/10.1016/j.msea.2011.01.067
6.
LePera
,
F. S.
, “
Improved Etching Technique to Emphasize Martensite and Bainite in High-Strength Dual-Phase Steel
,”
JOM
, Vol.
32
, No.
3
,
1980
, pp.
38
39
. https://doi.org/10.1007/BF03354553
7.
De Amar
,
K.
,
Speer
,
J. G.
, and
Matlock
,
D. K.
, “
Color Tint-Etching for Multiphase Steels
,”
Adv. Mater. Proc.
, Vol.
161
, No.
2
,
2003
, pp.
27
30
.
8.
Stojakovic
,
D.
, “
Electron Backscatter Diffraction in Materials Characterization
,”
Proc. Appl. Ceram.
, Vol.
6
, No.
1
,
2012
, pp.
1
13
. https://doi.org/10.2298/PAC1201001S
9.
Zhu
,
K.
,
Oberbillig
,
C.
,
Musik
,
C.
,
Loison
,
D.
, and
Iung
,
T.
, “
Effect of B and B+Nb on the Bainitic Transformation in Low Carbon Steels
,”
Mater. Sci. Eng. A
, Vol.
528
, No.
12
,
2011
, pp.
4222
4231
. https://doi.org/10.1016/j.msea.2011.02.022
This content is only available via PDF.
You do not currently have access to this content.