Thermoplastic polyurethanes (TPUs) are polymeric materials employed in a wide array of applications in the industrial field. Knowledge of their mechanical behavior is essential in order to obtain an accurate prediction of stresses and deformations resulting from loading. Mechanical and physical properties of these materials have been studied in the past, but their stress-strain behavior in the presence of cyclic loading has comparatively received much less attention. In this paper, experimental and constitutive modeling aspects concerning cyclic mechanical response of a TPU are investigated. The effect of imposing a cyclic strain on a TPU is studied by means of an experimental procedure based on alternate-symmetric tests in strain control at different strain levels and frequencies. During the tests, the increase in temperature due to the hysteretic heating can also be controlled by means of a compressed air cooling apparatus specifically devised. By taking advantage of the possibility of controlling and stabilizing temperature, the cyclic mechanical response can then be investigated at different temperatures and strain levels. A transient thermal analysis using finite element method (FEM) was also carried out to investigate temperature distribution on the specimen. TPU exhibited cyclic softening, and by comparing stabilized material response at different temperatures, cyclic softening was shown to be composed of a mechanical contribution and a thermal component. The TPU’s stress-strain curve changed considerably under cyclic loading conditions. In particular, cyclic softening was observed to increase with temperature and imposed cyclic strain, with a progressive shrinking of hysteresis loop passing from virgin condition to stabilized cyclic condition. Based on the experimental data, the cyclic curve could be determined as a function of temperature and could be fitted with a hyperelastic law in which material parameters are temperature dependent. The TPU exhibited significant sensitivity to cyclic loading, and this study demonstrated the importance of considering mechanical response in cyclic condition for design purposes. In particular, the identification of mechanical and thermal contributions to cyclic softening can be useful when studying fatigue failure mechanisms of these materials. Knowledge of cyclic curve can help when developing constitutive model for polymers to better predict a long-term behavior when cyclic loading is expected. The introduction of a dependence of cyclic curve on temperature allows considering simultaneously the new “material state” of the cycled polymer and, with some limitations, the thermal influence on mechanical response.
Skip Nav Destination
e-mail: andrea.avanzini@ing.unibs.it
Article navigation
April 2011
Research Papers
Effect of Cyclic Strain on the Mechanical Behavior of a Thermoplastic Polyurethane
A. Avanzini,
A. Avanzini
Department of Mechanical and Industrial Engineering,
e-mail: andrea.avanzini@ing.unibs.it
University of Brescia
, Via Branze 38, 25123 Brescia, Italy
Search for other works by this author on:
D. Gallina
D. Gallina
Department of Mechanical and Industrial Engineering,
University of Brescia
, Via Branze 38, 25123 Brescia, Italy
Search for other works by this author on:
A. Avanzini
Department of Mechanical and Industrial Engineering,
University of Brescia
, Via Branze 38, 25123 Brescia, Italye-mail: andrea.avanzini@ing.unibs.it
D. Gallina
Department of Mechanical and Industrial Engineering,
University of Brescia
, Via Branze 38, 25123 Brescia, ItalyJ. Eng. Mater. Technol. Apr 2011, 133(2): 021005 (9 pages)
Published Online: March 3, 2011
Article history
Received:
October 29, 2009
Revised:
September 27, 2010
Online:
March 3, 2011
Published:
March 3, 2011
Citation
Avanzini, A., and Gallina, D. (March 3, 2011). "Effect of Cyclic Strain on the Mechanical Behavior of a Thermoplastic Polyurethane." ASME. J. Eng. Mater. Technol. April 2011; 133(2): 021005. https://doi.org/10.1115/1.4003101
Download citation file:
Get Email Alerts
Evaluation of Machine Learning Models for Predicting the Hot Deformation Flow Stress of Sintered Al–Zn–Mg Alloy
J. Eng. Mater. Technol (April 2025)
Blast Mitigation Using Monolithic Closed-Cell Aluminum Foam
J. Eng. Mater. Technol (April 2025)
Irradiation Damage Evolution Dependence on Misorientation Angle for Σ 5 Grain Boundary of Nb: An Atomistic Simulation-Based Study
J. Eng. Mater. Technol (July 2025)
Related Articles
Characterization and Modeling of Large Displacement Micro-/Nano-Indentation of Polymeric Solids
J. Eng. Mater. Technol (October,2008)
Nonlinear Fractional Derivative Models of Viscoelastic Impact Dynamics Based on Entropy Elasticity and Generalized Maxwell Law
J. Comput. Nonlinear Dynam (April,2011)
Modeling of Fatigue Crack Propagation During Sliding Wear of Polymers
J. Eng. Mater. Technol (April,2003)
A Multi-Station Rolling/Sliding Tribotester for Knee Bearing Materials
J. Tribol (April,2004)
Related Proceedings Papers
Related Chapters
Changes in Surface Morphology and Microcrack Initiation in Polymers Under Simultaneous Exposure to Stress and Fast Atom Bombardment
Influence of Radiation on Material Properties: 13th International Symposium (Part II)
Chitosan-Based Drug Delivery Systems
Chitosan and Its Derivatives as Promising Drug Delivery Carriers
The Effect of Temperature on Polymer Supported Titanium Dioxide Photocatalyst for Degradation of Volatile Organic Compounds
International Conference on Computer and Electrical Engineering 4th (ICCEE 2011)